Pengendalian Kehilangan Minyak Di Final Effluent Menggunakan Metode Statistical Quality Control Pada Proses Pengolahan Crude Palm Oil PT XYZ

Main Article Content

Muhammad Reza Firdaus
Ema Lestari
Fatimah Fatimah
Sihabuddin Chalid

Abstract

PT XYZ is an agro-industrial company that focuses on palm oil processing, mainly producing Crude Palm Oil (CPO) and kernels. The main process carried out by the company is processing fresh fruit bunches (FFB) into CPO and palm kernel (kernel). The level of oil losses in PT's final effluent. XYZ should not exceed 0.40%, but in 3 months, there has been an increase that exceeds the company's standards. This condition can affect CPO production results. Therefore, this research was conducted to analyze oil loss in the final effluent. The method used is Statistical Quality Control (SQC) using three tools, namely Check Sheet to collect data, Histogram to show data distribution, and cause-and-effect diagram to assist in understanding and solving the problems faced. The research results showed that oil loss was the highest, 0.57% in October, 0.46% in November, and 0.45% in December 2023. Therefore, it is necessary to make recommendations for improvements using a cause and effect diagram that includes machine, human and method factors to meet the desired standards, factors that cause high oil losses including lack of attention to equipment maintenance, inconsistent machine cleaning times and overlooked oil citing momentum.

Article Details

Section
Articles
Author Biography

Fatimah Fatimah, {"en_US":"Politeknik Negeri Tanah Laut "}

Staf Pengajar pada Jurusan Teknologi Industri Pertanian, Politeknik Negeri Tanah Laut

References

Abdiansyah, W., Dharmawati, N.D. and Renjani, R.A. (2023) ‘Analisa Pengaruh Metode Pencucian Nozzle Sludge Centrifuge terhadap Kehilangan Minyak pada Final Effluent’, Agricultural Engineering Innovation Journal, 1(2), pp. 94–112. Available at: https://doi.org/10.55180/aei.v1i2.706.

Arifin, M.S., Adjie, S. and Santoso, E. (2019) ‘Pengendalian Kualitas Dengan Metode Seventools Sebagai Alat Untuk Mengurangi Produk Cacat Pada Perusahaan Tanteka Sablon Ponorogo.’, ISOQUANT : Jurnal Ekonomi, Manajemen dan Akuntansi, 3(1), p. 25. Available at: https://doi.org/10.24269/iso.v3i1.237.

Bakhtiar, Diana and Fariz (2017) ‘Seminar Nasional Teknik Industri’, Seminar Nasional Teknik Industri [SNTI2017], 4, pp. 13–14.

Devani, V. and Marwiji (2014) ‘Analisis Kehilangan Minyak Pada Crude Palm Oil (CPO) dengan Menggunakan Metode Statistical Process Control’, Jurnal Ilmiah Teknik Industri, 13(1), pp. 28–42.

Hamdani, D. (2022) ‘Pengendalian Kualitas Dengan Menggunakan Metode Seven Tools Pada PT X’, Jurnal Ekonomi, Manajemen dan Perbankan (Journal of Economics, Management and Banking), 6(3), p. 139. Available at: https://doi.org/10.35384/jemp.v6i3.237.

Kasim, M. and Saputra, A. (2022) ‘Penelitian Kehilangan Minyak (Oil Losses) Tandan Kosong dan Air Rebusan Pada Stasiun Sterilizer Menggunakan Metode Fauilit Tree Analysis (Studi Kasus: PT. Ujong Neubok Dalam Kabupaten Nagan Raya’, SITEKIN: Jurnal Sain, Teknologi dan Industri, 19(2), pp. 262–269.

Nofirza et al. (2023) ‘Analisis Oil Losses Pada Stasiun Perebusan Produksi Crude Palm Oil (CPO) Menggunakan Metode Statistical Process Control (SPC)’, Jurnal Teknologi dan Manajemen Industri Terapan, 2(2), pp. 98–110. Available at: https://doi.org/10.55826/tmit.v2i2.67.

Nurrahman, A., Permana, E. and Musdalifah, A. (2021) ‘Analisa Kehilangan Minyak (Oil Losses) Pada Proses Produksi Di Pt X’, Jurnal Daur Lingkungan, 4(2), p. 59. Available at: https://doi.org/10.33087/daurling.v4i2.89.

Sekarwangi, R. and Pramestari, D. (2022) ‘Analisis Pengendalian Kualitas dengan Metode Statistical Quality Control di PT. Sunstar Engineering Indonesia’, IKRAITH-Teknologi, 7(1), pp. 11–20. Available at: https://doi.org/10.37817/ikraith-teknologi.v7i1.2315.

Ulimaz, A. et al. (2021) ‘Analisis Oil Losses Pada Proses Pengolahan Minyak Inti Kelapa Sawit di PT. XYZ Dengan Metode Seven Tools’, Jurnal Teknologi Agro-Industri, 8(2), pp. 124–134. Available at: https://doi.org/10.34128/jtai.v8i2.144.

Most read articles by the same author(s)

1 2 3 > >>